Hydrogen producer gas

Hydrogen sulfide gas Hydrogen sulfide is a gas with a rotten egg odor. This gas is produced under anaerobic conditions. Hydrogen sulfide is particularly dangerous because it dulls your sense of smell so that you don t notice it after you have been around it for a while and because the odor is not noticeable in high concentrations. The gas is very poisonous to your respiratory system, explosive, flammable, and colorless. 

The most common contaminants in produced gas are carbon dioxide (COj) and hydrogen sulphide (HjS). Both can combine with free water to cause corrosion and H2S is extremely toxic even in very small amounts (less than 0.01% volume can be fatal if inhaled). Because of the equipment required, extraction is performed onshore whenever possible, and providing gas is dehydrated, most pipeline corrosion problems can be avoided. However, if third party pipelines are used it may be necessary to perform some extraction on site prior to evacuation to meet pipeline owner specifications. Extraction of CO2 and H2S is normally performed by absorption in contact towers like those used for dehydration, though other solvents are used instead of glycol. 

The oxidation of metals by water vapor is carried out in experiments fixing the partial pressures of water and hydrogen (produced gas). The simultaneous presence of these two gases involves, by the action of the chemical equilibrium in gas phase, a partial pressure of oxygen. 

If produced gas contains water vapour it may have to be dried (dehydrated). Water condensation in the process facilities can lead to hydrate formation and may cause corrosion (pipelines are particularly vulnerable) in the presence of carbon dioxide and hydrogen sulphide. Hydrates are formed by physical bonding between water and the lighter components in natural gas. They can plug pipes and process equipment. Charts such as the one below are available to predict when hydrate formation may become a problem. 

To enable interchangeabiUty of the SNG with natural gas, on a calorific, flame, and toxicity basis, the synthetically produced gas consists of a minimum of 89 vol % methane, a maximum of 0.1% carbon monoxide, and up to 10% hydrogen. The specified minimum acceptable gross heating value is approximately 34.6 MJ/m (930 Btu/fE). 

Synthetic jet fuel derived from coal is even more difficult and expensive, since the best of the conversion processes produces a fuel very high in aromatics. With hydrogenation, overall thermal efficiency is only 50%. Without additional hydrogenation, the gas turbine fuels would contain 60—70% aromatics. 

Steam also is blended with air in some gasification units to promote the overall process via the endothermic steam—carbon reaction to form carbon monoxide and hydrogen. This was common practice at the turn of the nineteenth century, when so-called producer gasifiers were employed to manufacture LHV gas from different types of biomass and wastes. The producer gas from biomass and wastes had heating values around 5.9 MJ /mr at 

An acid was once defined simply as a substance which produces hydrogen ions, or protons. However, the simple proton, H , is never found under ordinary conditions, and this definition required amendment. Bronsted and, independently, Lowry, therefore redefined an acid as a susbstance able to donate protons to other molecules or ions, and a base as a substance capable of accepting such protons. If we consider hydrogen chloride, HCl, as an example, the HCl molecule is essentially covalent, and hydrogen chloride (gas or liquid) contains no protons. But anhydrous hydrogen chloride in benzene will react with anhydrous ammonia  

Corrosion products and deposits. All sulfate reducers produce metal sulfides as corrosion products. Sulfide usually lines pits or is entrapped in material just above the pit surface. When freshly corroded surfaces are exposed to hydrochloric acid, the rotten-egg odor of hydrogen sulfide is easily detected. Rapid, spontaneous decomposition of metal sulfides occurs after sample removal, as water vapor in the air adsorbs onto metal surfaces and reacts with the metal sulfide. The metal sulfides are slowly converted to hydrogen sulfide gas, eventually removing all traces of sulfide (Fig. 6.11). Therefore, only freshly corroded surfaces contain appreciable sulfide. More sensitive spot tests using sodium azide are often successful at detecting metal sulfides at very low concentrations on surfaces. 

---