Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Amorphous materials glass transition temperature

PVC is an amorphous polymer (glass transition temperature = 220 °F, 105 °C). As a result, it has good clarity. Another important characteristic is that it can be extruded either as a rigid material or as a flexible material by adding a plasticizer to the polymer. Rigid films can be metallized and punched into sequins for dressmaking applications. Flexible films are used to overwrap clothing and other textile products. [Pg.13]

Irregularities such as branch points, comonomer units, and cross-links lead to amorphous polymers. They do not have true melting points but instead have glass transition temperatures at which the rigid and glasslike material becomes a viscous liquid as the temperature is raised. [Pg.1006]

As appHed to hydrocarbon resins, dsc is mainly used for the determination of glass-transition temperatures (7p. Information can also be gained as to the physical state of a material, ie, amorphous vs crystalline. As a general rule of thumb, the T of a hydrocarbon resin is approximately 50°C below the softening point. Oxidative induction times, which are also deterrnined by dsc, are used to predict the relative oxidative stabiHty of a hydrocarbon resin. [Pg.350]

The melt temperature of a polyurethane is important for processibiUty. Melting should occur well below the decomposition temperature. Below the glass-transition temperature the molecular motion is frozen, and the material is only able to undergo small-scale elastic deformations. For amorphous polyurethane elastomers, the T of the soft segment is ca —50 to —60 " C, whereas for the amorphous hard segment, T is in the 20—100°C range. The T and T of the mote common macrodiols used in the manufacture of TPU are Hsted in Table 2. [Pg.344]

In the case of an amorphous polymer the glass transition temperature will define whether or not a material is glass-like or rubbery at a given temperature. If, however, the polymer will crystallise, rubbery behaviour may be limited since the orderly arrangement of molecules in the crystalline structure by necessity limits the chain mobility. In these circumstances the transition temperature is of less consequence in assessing the physical properties of the polymer. [Pg.64]

On comparison of the yield strengths and elastic moduli of amorphous polymers well below their glass transition temperature it is observed that the differences between polymers are quite small. Yield strengths are of the order of 8000 Ibf/in (55 MPa) and tension modulus values are of the order of 500 000 Ibf/in (3450 MPa). In the molecular weight range in which these materials are used differences in molecular weight have little effect. [Pg.74]

In a semicrystalline polymer, the crystals are embedded in a matrix of amorphous polymer whose properties depend on the ambient temperature relative to its glass transition temperature. Thus, the overall elastic properties of the semicrystalline polymer can be predicted by treating the polymer as a composite material... [Pg.506]

The presence of a solvent, especially water, and/or other additives or impurities, often in nonstoichiometric proportions, may modify the physical properties of a solid, often through impurity defects, through changes in crystal habit (shape) or by lowering the glass transition temperature of an amorphous solid. The effects of water on the solid-state stability of proteins and peptides and the removal of water by lyophilization to produce materials of certain crystallinity are of great practical importance although still imperfectly understood. [Pg.617]

At room temperature, atactic polystyrene is well below its glass transition temperature of approximately 100 °C. In this state, it is an amorphous glassy material that is brittle, stiff, and transparent. Due to its relatively low glass transition temperature, low heat capacity, and lack of crystallites we can readily raise its temperature until it softens. In its molten state, it is quite thermally stable so we can mold it into useful items by most of the standard conversion processes. It is particularly well suited to thermoforming due to its high melt viscosity. As it has no significant polarity, it is a good electrical insulator. [Pg.338]


See other pages where Amorphous materials glass transition temperature is mentioned: [Pg.96]    [Pg.96]    [Pg.312]    [Pg.130]    [Pg.314]    [Pg.328]    [Pg.142]    [Pg.281]    [Pg.286]    [Pg.468]    [Pg.503]    [Pg.341]    [Pg.333]    [Pg.35]    [Pg.530]    [Pg.531]    [Pg.190]    [Pg.261]    [Pg.44]    [Pg.75]    [Pg.185]    [Pg.144]    [Pg.145]    [Pg.30]    [Pg.56]    [Pg.318]    [Pg.357]    [Pg.267]    [Pg.395]    [Pg.402]    [Pg.404]    [Pg.595]    [Pg.595]    [Pg.623]    [Pg.688]    [Pg.133]    [Pg.167]    [Pg.393]    [Pg.205]    [Pg.284]    [Pg.114]    [Pg.115]   
See also in sourсe #XX -- [ Pg.2079 ]




SEARCH



Amorphous glasses

Amorphous materials

Amorphous transition temperature

Glass material

Temperature amorphization

© 2024 chempedia.info