a | b | c | d | e | f | g | h | i | j | k | l | m | n | o | p | q | r | s | t | u | v | w | x | y | z

   |<      <<      >>     > |    


Typical temperatxire T versus mole fraction v diagrams for the constant-pressure paths shown in figure A2.5.11. Note the critical points and the horizontal tliree-phase lines.

Typical tensile behaviour of fibres

Typical Tension-Tension Fatigue Data

Typical Tension-Tension Fatigue Data

Typical test results for a 400-ml butane fireball diameter

Typical test results of a medium-capacity spiral lobe compressor vacuum pump using intermeshing lobes. Used by permission

Typical thermal stratification of a lake, reservoir, or poorly mixed estuary in summer which, because of density differences, estabUshes discrete 2ones

Typical three-stage stator-rotor starter

Typical thrust bearing temperature sensor installation.

Typical time-current characteristics of 6.6 kV HRC fuses

Typical time-of-flight spectra of DF products from the F D2 reaction - The collision energies and in-plane and out-of-plane laboratory scattered angles are given in each panel. The DF product vibrational quantum number associated with each peak is indicated. Reprinted with pennission from Faiibel etal . Copyright 1997 American Chemical Society.

Typical tip morphology obtained after high-temperature treatment .

Typical torque curves for NEMA design B, C and D Induction motors having synchronous speeds below 1,800 rpm. These curves also apply to some 1,800 rpm design motors. Used by permission

Typical torque versus speed curves for eddy current brakes.

Typical torque-speed characteristics of wound-rotor motors ,

Typical torsional interference map.

Typical TPG valve arrangement.

Typical trailing edge repair. Reproduced by permission of the Boeing Company.

Typical transformer vector groupings and connection arrangements

Typical trickle valve .

Typical tube bundle using fabricated or cast end headers. Used by permission

Typical tube bundle using flanged end cover plates. Used by permission

Typical union type disk holders. They are not all available. By permission, B.S. B. Safety Systems, Inc.

Typical use of saturable inductors in reducing reverse recovery losses.

Typical vacuum systems holding vacuum on a vessel. By permission, Nash Engineering Co.

Typical value chain for 1 ha U.S. beet sugar production. See text.

Typical values of the washout coefficient as a function of rainfall rate and particle diameter. Source

Typical valve codes and specifications. By permission, Borden Chemicals and Plastics Operating Limited Partnership.

Typical variable inlet vane performance curves. Used by permission

Typical variation of , 2 and loss tangent for a viscoelastic material

Typical variation of mean penetration height with adhesion .

Typical velocity triangles for an axial-flow compressor.

Typical velocity triangles for different size particles.

Typical venturi scrubber configuration.

Typical vertical alignment of cavities resulting from cavitation damage in a diesel engine cylinder liner.

Typical vertical tube-side thermosiphon reboiler. Used by permission

Typical vessel baffles to improve mixing performance. Adapted modified by permission, Casto, L. V., Chem. Engr., Jan. 1, 1972, p. 97 .

Typical vessel external jackets for heat transfer.

Typical vibrational progression intensity distributions

Typical volute-type pump .

Typical wire mesh efficiency.

Typical wire mesh mist eliminator pressure drop curves for one style of mesh at three different liquid loadings. Others follow similar pressure drop patterns. By permission, Otto H. York Co., Inc.

Typical X-ray spectra

Typical zones on a extruder screw

Typicetl installation of mesh strips in vertical vessel. Courtesy of Otto H. York Co., Inc.

Typioai industriai gas turbine.

Typioai proteotion system for a turbine.

Typioal metal-flexing dise eoupling.

U C sion turbines.

U face of solid Xe. The interval between the isopotential lines is 1-66 x 10 J. After



   |<      <<      >>     > |